Sliding Gate Motor Installation — Abu Dhabi

No. Emirtech installs and services CAME, BFT, FAAC, Nice, Beninca, Sommer and LiftMaster sliding gate operators commercially with field experience across Abu Dhabi — we are NOT an authorised distributor, master dealer or tier-1 partner of any gate-automation brand. Hardware is sourced through authorised UAE channels with original manufacturer warranty preserved. Emirtech installs and programmes Control4 working with a third-party authorised dealer and holds no manufacturer-level credential of its own.

Through a free site survey. We measure gate weight, length, rolling resistance and traffic frequency, then check power supply (single or three-phase) and civil readiness. Residential villa gates up to 800kg typically use CAME BX or Nice RUN; mid-range 1000kg-1500kg gates use BFT ARES; industrial 2000kg+ gates use BFT ICARO or LiftMaster three-phase operators. Under-spec motors fail early, so sizing is matched to actual duty cycle.

Yes. We integrate operator triggers with ANPR cameras for whitelisted number plates, RFID long-range readers for staff and fleet vehicles, GSM intercoms for visitors, key fobs for residents, push-button stations at gatehouses and ground induction loops for exit detection. Multi-method entry can be configured per site, with manual key-switch override always available as a fallback.

Yes. Battery backup units are an option on most CAME, BFT, FAAC and Nice control boards, providing a limited number of operation cycles after mains loss depending on motor draw and battery capacity. Useful for compounds, warehouses and 24/7 logistics yards where loss of gate function would block emergency vehicles or shift changes.

Yes. Annual maintenance contracts cover scheduled visits — greasing of rack and pinion, alignment checks, photocell beam testing, control-board diagnostics, battery health checks, remote re-coding and minor parts replacement. Reactive call-out is included, on the arrangements agreed in the written quotation. AMC tiers are scoped to site count and premises type during the survey.

Yes. We diagnose and repair automatic gates and boom barriers of any brand in Abu Dhabi and Al Ain, whoever installed them, with a reply the same working day; Al Ain is served from our Mussafah office. See automatic gate and barrier repair.

Call +971 55 651 7843 or request a free sliding gate motor installation consultation. Share your gate weight, length, location, current motor (if any) and intended access methods. A specialist will respond with a scoped proposal once the survey is done.

Yes. A sliding gate motor has a manual release, normally a key or lever that disengages the drive so the gate can be pushed along its track by hand. Release it only while the gate is stationary and clear of people and vehicles, move it slowly, and re-engage the release afterwards. Our installations include a key-switch override. If the gate will not move freely by hand, there may be debris in the track or a mechanical fault, so stop and call an installer.

Check the mains supply first, because a tripped breaker or isolator is a common cause after a power cut or storm. Then check that the photocell lenses are clean and unblocked, that the track is clear of sand, debris or standing water, and whether the control board shows a fault light. A battery backup unit, where fitted, can be flat after a long outage. Free the gate with the manual release if you need to close it. If the motor still does not respond, trips the breaker again or the gate has left its track, stop and call us for gate motor repair rather than opening the control box.

Yes, as supply-and-install projects: survey, motor sizing, installation and commissioning, with repair or maintenance afterwards. Equipment is sourced through authorised UAE channels with original manufacturer warranty, and Emirtech is not an authorised dealer or distributor of any gate brand. Abu Dhabi is served from our Mussafah base; Al Ain jobs are by appointment on scheduled visits, as we have no Al Ain office.

A motor is usually worth repairing when the fault is a single part, such as a remote receiver, photocell, limit switch or control board, and the gate rolls freely by hand. Replacement is worth considering when the same faults keep returning, spare parts for the model are no longer available, the motor overheats or stops under load even though the track is clean and free-running, the casing or gearbox is damaged by water or impact, or the motor was never sized for the weight and use of the gate. Check first that the gate moves freely when the motor is released, because a worn track or wheels can make a healthy motor look faulty. We inspect, tell you which applies and quote in writing; see our gate and barrier repair page.

The main factors are the weight and length of the gate, the condition and level of the track and wheels, how often the gate is used each day, the power supply available on site and the safety devices fitted. A heavy or long gate needs a motor chosen with margin above its real load, and a free-running gate matters as much as a stronger motor, because a stiff track overloads any drive. A busy commercial entrance needs a motor suited to frequent use, and the photocells and safety edges must suit the gate. We confirm the choice at a site survey and give a written quotation.