CAME Gate Barrier Installation & Service — Abu Dhabi

No. Emirtech installs CAME commercially with field experience — we are NOT an authorised CAME distributor or master dealer, and we do not claim CAME S.p.A. tier-1 reseller status. We source CAME GARD barriers, BX sliding motors and ATI/FAST swing operators through legitimate UAE channels and install them to a high standard across Abu Dhabi and Al Ain. Sites under manufacturer warranty are handled with the original supplier in the loop where required.

Lane width and duty cycle decide the model. Larger GARD models cover wider lanes and heavier daily cycles for busy commercial entries, and we confirm the maximum clearance width of the exact model against the current CAME datasheet before specifying it. We survey the site, measure the opening and propose the right barrier with photocells, induction loops and the appropriate access control inputs.

Yes. We service existing CAME installations regardless of the original installer. Typical jobs include ZL control board replacement, motor and capacitor service, photocell alignment, induction loop fault tracing, mast repair after vehicle strike, sliding gate rack realignment and full recommissioning. We provide an honest fault report, parts list and itemised written quotation before starting works.

Yes. CAME ZL control boards accept dry-contact open commands from ANPR cameras, long-range RFID readers, push-button stations, key switches, GSM units and access control panels. We wire and commission the integration, set free-exit loops, presence loops and safety photocells, and test end-to-end. Common use cases include unmanned compound entries, staff car parks and visitor lanes with intercom call-out.

Yes. Our main coverage and our ADMCC approval are for Abu Dhabi and Al Ain; Emirtech also takes Dubai CAME gate and barrier projects itself, not through partners. Emirtech also holds no SIRA licence, so any SIRA-regulated electronic security element in Dubai is not included. For a site in Abu Dhabi or Al Ain, tell us the location and we will confirm what we can take on.

Call +971 55 651 7843 or request a free CAME gate barrier consultation. Share your site location, lane width or gate leaf size, traffic volume, existing CAME equipment model numbers if any, and current installation photos. A specialist will respond with a scoped proposal once the survey is done.

Yes. Emirtech has no Dubai office, so we schedule Dubai visits from Mussafah, and our own engineers fit and repair CAME BX sliding motors, ATI and FAST swing operators and GARD barriers there. Send the location, the gate type and any CAME model numbers and we will confirm the scope. Emirtech holds no SIRA approval; SIRA-regulated CCTV, alarm and access-control work in Dubai goes through SIRA-approved partners. We are not an authorised CAME distributor. See gate barrier systems in Dubai.

For a villa sliding gate we fit a CAME BX motor chosen within its rated leaf weight, and for a villa swing gate an ATI or FAST operator on a single or double leaf. For a warehouse or factory sliding gate, BX motors again. For a compound, labour camp or car park entry we use GARD road barriers, with lane width deciding between GARD 4, 6, 8 and 12. We confirm every model against the current CAME datasheet at the survey.

Check the mains supply and breaker first, as a power cut is a common cause. After a storm or heavy rain, look for water in the control cabinet; a gate that has lost its position or tripped on an obstruction may need its limits and force settings reset. Clean the photocells and clear the track or barrier path, and never bypass the safety devices. If the fault remains, we diagnose ZL control boards, motors, capacitors, photocells and induction loops on CAME sites in Abu Dhabi, Al Ain and Dubai (Dubai by appointment), whoever installed them. See automatic gate and barrier repair.

Look for the nameplate or label on the motor or barrier housing and on the control board. Note the model name (for example a GARD, BX, ATI or FAST series name), any serial or batch code and, for a barrier, the arm length fitted. Send a photo of the label and the unit with your location so a technician can plan the service and bring suitable parts. If there is no label, we identify the unit on site where we can. Dubai visits are by appointment.

We source CAME spare parts, barrier arms and remote controls through legitimate UAE supply channels. Availability varies by model and age, so we cannot promise any part before checking it. Emirtech is not a CAME dealer, distributor or service centre. Send the model number or a photo and we confirm in the written quotation what can be supplied.

A visit normally covers the operator and control board, safety photocells and edge sensors, induction loops where fitted, limit and force settings, lubrication and wear on the rack, hinges, arm or gearbox, the remote controls and the manual release, followed by a short written note of anything that needs repair. Annual maintenance contracts also include fault response. The scope is agreed in writing before the contract starts.