Arc-Fusion Splicing
Calibrated arc-fusion splicer alignment with a target below 0.02 dB per splice. Each joint is protected in a heat-shrink sleeve, secured in a labelled splice tray and OTDR-verified before handover.
Fibre Splicing · Abu Dhabi
Fibre Splicing & Termination Services — Abu Dhabi
Precision fusion splicing, pigtail termination and field-polish connector installation for single-mode and multi-mode fibre networks across Abu Dhabi Emirate — each joint OTDR-verified to TIA-568 standards.
Get a free site survey Talk to a specialist
Free Site Survey
Control4 installer
Since 2018
Honest Scope
In short: Fibre splicing and termination decide whether an optical backbone delivers its design capacity. Fusion splicing joins two bare fibres with an electric arc and targets an insertion loss below 0.02 dB per splice, the lowest-loss permanent joint. Mechanical splicing, typically 0.1 to 0.3 dB, is an interim method where fusion is impractical and is unsuitable for long backbone runs. Termination turns a raw fibre end into a connector interface, either by fusion-splicing a factory-polished SC, LC or ST pigtail or by field polishing on site.
Fibre Splicing & Termination Services: key facts
| Who provides it? | Emirtech Technology, based at M44, Mussafah Industrial Area, Abu Dhabi, in operation since 2018. The work is carried out by Emirtech's own engineers. |
|---|---|
| Where? | Abu Dhabi and Al Ain, served from Emirtech's Mussafah, Abu Dhabi base; there is no Al Ain office. In Dubai: smart home, PABX and IP-PBX phone systems, IT AMC and time attendance by scheduled on-site visits, gate barriers, ANPR, video intercoms and turnstiles by Emirtech itself; CCTV, alarm and access control through SIRA-approved partners, with Emirtech coordinating. |
| What is covered | Fibre Splicing & Termination Services. |
| Survey and quotation | Emirtech publishes no price list: it surveys or assesses first and then gives a written, itemised quotation. |
| Credentials | Emirtech is an independent systems integrator. It holds no manufacturer-level credential of its own, and its ADMCC approval covers security systems only, not IT services. |
| Last reviewed | 21 October 2026 |
What do professional fibre splicing and termination services involve?
Fibre splicing and termination are the two decisive trades that determine whether an optical backbone delivers its design capacity or haemorrhages signal at every junction. Fusion splicing uses an arc-fusion splicer to align two bare glass fibres and fuse them with a controlled electric arc, targeting an insertion loss below 0.02 dB per splice — the lowest-loss permanent joint achievable. Mechanical splicing serves as a measured interim method where fusion is impractical, though its typical 0.1–0.3 dB loss makes it unsuitable for long backbone runs. Termination converts a raw fibre end into a connectorised interface: pigtail termination pre-fuses a factory-polished connector (SC, LC or ST) to a short fibre tail, which is then fusion-spliced to the incoming cable for a considered, low-loss result; field-polish termination cleaves the fibre on site and polishes it into a connector, offering speed where pigtails are unavailable. Both methods demand exacting splice-tray management — every fibre is routed with a minimum bend radius, secured in the tray, and colour-coded to TIA-598 fibre colour standards for traceable documentation. At Emirtech Technology, an integrator (ADMCC-approved for security systems) operating from M44, Mussafah Industrial Area, Abu Dhabi since 2018, we execute every splice with calibrated arc-fusion equipment and verify each joint with a full OTDR trace plus insertion-loss and return-loss measurement per TIA-568. Whether the scope is a 12-fibre pigtail tray in an office comms room or a 288-core ribbon splice in a campus fibre-optic cabling installation, every termination is logged, labelled and cross-referenced to the structured cabling as-built drawings. We supply both loaded and unloaded fibre patch panels, selecting density and connector type to match your rack or data-closet layout, and we document fibre polarity (A-B or universal) so future moves and changes remain straightforward. We do not publish a price list: splicing is priced by fibre count, site access and cable construction, and patch-panel termination with OTDR certification by the fibre count per tray and the number of trays. Every job starts with a site walkthrough, after which we send a written, itemised quotation. To discuss your fibre backbone or arrange a survey, call +971 55 651 7843 or request a quotation online.
Fibre Splicing & Termination
Core fibre termination disciplines we deliver
Pigtail & Field-Polish Termination
Factory-polished pigtails fused to incoming fibre for minimal connector loss, or precision field-polish SC/LC/ST connectors where speed is paramount. Both methods documented to TIA-598 colour coding.
Patch-Panel Build & Loading
Loaded or unloaded fibre patch panels selected to match rack density. Polarity mapped, adaptor plates labelled and fibre slack managed with documented bend-radius compliance throughout the enclosure.
OTDR Trace & IL/RL Certification
Every terminated fibre receives an OTDR trace, insertion-loss and return-loss measurement per TIA-568. Digital test reports are delivered with the as-built package for ongoing asset management.
Before you commission a fibre splice
A considered fibre termination scope starts well before the splicer is powered on. Confirm your fibre type, connector standard and patch-panel density against the items below, then call +971 55 651 7843 or request a free site survey so we can verify cable condition, route access and tray capacity on the ground.
- Confirm fibre type: single-mode OS2 or multi-mode OM3/OM4/OM5
- Specify connector standard required: SC/UPC, LC/UPC, SC/APC or LC/APC
- Define splice method: fusion (permanent backbone) or mechanical (interim/emergency)
- Select patch-panel format: loaded with adaptors or unloaded for staged build-out
- Verify fibre count per cable and total splice-tray capacity needed
- Establish polarity scheme: A-B straight-through or universal method
- Confirm TIA-598 colour-coding convention for tube and fibre identification
- Check that adequate fibre slack is coiled at each termination point (minimum 3 m)
- Determine OTDR certification wavelength: 1310/1550 nm (SM) or 850/1300 nm (MM)
- Identify if existing splices require re-fusion or additional pigtail additions
- Agree labelling convention for patch-panel ports and splice-tray positions
- Confirm as-built documentation format: digital PDF trace files plus spreadsheet register
Fibre Termination Standards
Why measured fibre termination matters
Loss-Budget Assurance
Every splice and connector adds to the link loss budget. Precision fusion keeps each joint below 0.02 dB, preserving headroom for longer runs, higher bit-rates and future wavelength-division multiplexing.
TIA-598 Colour Discipline
Strict adherence to tube and fibre colour sequencing ensures any technician can identify a strand years later without tone-testing, reducing mean time to repair and eliminating cross-connection risk.
Splice-Tray Craft
Fibres routed at or above minimum bend radius, heat-shrink sleeves seated in dedicated channels, and slack managed without stress. Disciplined tray work prevents latent macro-bend attenuation that surfaces under temperature shift.
Traceable Certification
OTDR traces, IL and RL readings stored per fibre per link create a baseline. Future troubleshooting compares current traces against the original certified values, isolating degradation to a specific joint or segment.
Scope — what we deliver and explicitly do not
Emirtech Technology operates as a fibre and structured-cabling integrator and ADMCC-approved installer for security systems across Abu Dhabi Emirate. The following scope statements define what a fibre splicing and termination engagement includes and where our remit ends.
- We deliver: arc-fusion splicing (single-mode and multi-mode), pigtail termination, field-polish connector installation (SC/LC/ST, UPC and APC), fibre patch-panel build and loading, splice-tray management, OTDR trace and IL/RL certification per TIA-568, fibre colour-coding to TIA-598, labelling, as-built documentation and ongoing maintenance contracts.
- We do not deliver: fibre cable manufacture, submarine or aerial fibre installation beyond building entry, dark-fibre leasing, wavelength-division multiplexing equipment supply without an integration scope, or standalone telecoms carrier licensing services.
- We are not: a telecoms operator, an internet service provider, a fibre cable manufacturer, or a data-centre colocation provider. Emirtech is an integration and contracting firm that installs, splices, terminates and certifies fibre infrastructure within client premises and campus environments.
- We are not affiliated with: Corning, CommScope, Panduit, Belden, Legrand or any fibre cable manufacturer as a channel partner or authorised distributor. We procure materials through authorised UAE supply channels and install to manufacturer specifications.
- All fibre splicing and termination work within Abu Dhabi Emirate is covered by the ADMCC-regulated electronic-security scope only where it forms part of a security system; our ADMCC approval covers security systems work only.
- This page gives no prices; cost is survey-dependent. Final pricing requires a site walkthrough to assess cable condition, route access, fibre count and termination complexity.
For a detailed scope discussion or to arrange an on-site fibre survey, contact our Mussafah office on +971 55 651 7843 or email [email protected].
Common questions
FAQs
What is the difference between fusion splicing and mechanical splicing for fibre cables?
Fusion splicing permanently fuses two glass fibre ends using a controlled electric arc, achieving insertion loss typically below 0.02 dB per joint. Mechanical splicing aligns the fibres in a precision holder with index-matching gel, producing a semi-permanent joint with 0.1 to 0.3 dB loss. Fusion is the preferred method for permanent backbone runs where every fraction of a decibel matters; mechanical splicing serves as a measured interim solution for emergency restoration or temporary links where a fusion splicer cannot be deployed.
When should I choose pigtail termination over field-polish connectors?
Pigtail termination fuses a factory-polished connector assembly to the fibre, delivering connector-grade loss consistency because the critical end-face is machine-finished under controlled conditions. Field-polish connectors are cleaved and polished on site, which is faster but depends heavily on technician skill and ambient conditions. For backbone terminations, high-density patch panels and links carrying 10G or above, pigtails are the considered choice. Field-polish connectors suit low-count drops or situations where pigtail stock is unavailable and a same-day handover is required.
How is a fibre splice certified after termination?
Each terminated fibre receives three measurements: an OTDR (Optical Time-Domain Reflectometer) trace that maps every event along the fibre length including splices, connectors and bends; an insertion-loss test that measures total end-to-end attenuation; and a return-loss test that quantifies back-reflections at each connector interface. Results are compared against TIA-568 thresholds for the relevant fibre class (OS2, OM3, OM4). Emirtech delivers digital PDF trace files and a tabulated register per fibre as part of the as-built documentation package.
What fibre types and connector standards does Emirtech terminate?
We terminate single-mode OS2 and multi-mode OM3, OM4 and OM5 fibre in all common connector formats: SC/UPC, SC/APC, LC/UPC and LC/APC. ST connectors are supported for legacy installations. Patch panels are available in both loaded configurations with pre-installed adaptor plates and unloaded frames for staged build-out. Polarity is documented to the chosen scheme, whether A-B straight-through or the universal method specified in TIA-568.
What does fibre splicing and termination typically cost in Abu Dhabi?
We do not publish a price list, because the cost is survey-dependent. A single-mode fusion splice is priced by fibre count, cable access and whether the cable is ribbon or loose-tube construction. Full patch-panel termination with OTDR certification depends on the fibre count per tray and the number of trays. Multi-mode splicing is priced on the same drivers. After a site walkthrough to assess route complexity, existing infrastructure condition and total fibre count, we send a written, itemised quotation.
How do I request a fibre splicing and termination quotation from Emirtech?
Call +971 55 651 7843 to speak with our fibre team directly, or submit your requirements through the online quotation form. Provide the fibre type (single-mode or multi-mode), approximate fibre count, connector standard required and site location within Abu Dhabi Emirate. We will arrange a site survey to verify cable condition, route access and splice-tray capacity before delivering a detailed, obligation-free quotation.
Fibre Splicing · Abu Dhabi
Talk to an Abu Dhabi specialist
Free site survey · transparent scope · honest costs · ADMCC-approved for security systems · Mussafah M44 home base since 2018.
Need a free Abu Dhabi site visit? Call +971 55 651 7843 or email [email protected] — we reply the same working day across Abu Dhabi and Al Ain.